Service manuals, schematics, eproms for electrical technicians

PANASONIC TX-25,29AD20.

TV - SERVICE MANUAL
Type: (DJVU)
Size
185.2 KB
Page
6
Category
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    PANASONIC TX-25 TX25 29AD20. TX 25 29 AD 20
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic_TX 28 DK 1F nincs kép_hang és TXT van.
Sziasztok, a fenti pana Euro 4 a fenti hibát csinálja, tápok mérve jónak tünnek, VDP 3120 van benne. AV-ról sincs kép. Szinek jók a texten. Ebben a kérdéskörben kérnék tanácsot. Köszönettel. Imre
RGB Mod in Panasonic CTP-2780SF

Anyone ever do one of these to a CRT?

Seems like the set has this jungle IC which will be where the RGB lines
for the OSD are needed for the mod:

https://pdf1.alldatasheet.com/datasheet-pdf/view/13342/PANASONIC/AN5304NK.html

Am not sure what the line would be that tells the chip to turn the OSD on. Apparently there
is a line if its 1 volt or more, it activates the OSD, if zero its normal video.

Also I think there must be a sync line tapped into which is bought out to the rear of the set,
with the (3) RGB lines / jacks but not sure where that would be tapped into?

I am gonna use BNC jacks, not the scart connector.
There are some youtube videos about RGB modding and lots of topics on the shumps
forums but so far it seems no one has tried this with Panasonic.

 

Steve Hearns
Technotronic Dimensions, VT [USA]
WWW.TECHNOTRONIC-DIMENSIONS.COM

Panasonic TX-P42C2E plamza z-sus zárlat
Jó Napot Kedves Kollégák!
A fenti plazma 4-es hibakóddal érkezett. Z-sus panelon az RJP30E4 igbt-ken zárlat van.
A csatlakozókat lehúzva az Y-sus-on pár mp-re megjelenik a 190V, majd lekapcsol és 7-es hibakódot villog.
Tapasztaltabb kollégákat kérdem: z-sus nélkül elindul ez a tv?Mert ha jól emlékszem a Samsung igen.
Illetve az IGBT-k cseréjével megúszom e?(Tudom ez jóslás kategória). Vagy elment az Y is? Azon nem találok hibás alkatrészt.
Köszönöm.üdv,kovi
PANASONIC TC 26B 3EE program memorizálás
Üdv mindenkinek!Segitségre lenne szükségem . Van egy Panasonic TC26B 3EE tipusu tv készülékem amely müködöképes ,csak annyi a probléma vele hogy a kábel tv adásai közül a VHF sáv felsö végén lévö csatornát nem tudom memorizálni sehogy sem.Probáltam az automata kereséssel de átmegy rajta és folytatja a keresést az UHF sávon tovább. Probáltam manuális kereséssel is és amikor megtaláltam az illetö csatornát akkor hiába probáltam memorizálni a PRE gombal mert miután más csatornára váltok és visza akarok térni az illetö csatornára akkor már nincs sehol vagyis nem memorizálta az illetö csatornát a tv.Ez a jelenség csak itt fordul elö a VHF sáv legfelsö végén a többi állomásokat beálitja automatikus ,valamint manuális kereséssel is és memorizálja is annak rendje és módja szerint.Arra gondoltam hogy esetleg lehet e valahogy a szervizmenübe belépni és a hangoló feszültség értékét egy kicsit kitolni hogy átfogja az egész sávot arra gondoltam hogy talán nem elég a sávátfogása mert más tv ken az általam nem memorizálhato állomás fölött is van még két adó de ezt már az én tvm "nem is látja"...Elöre is köszönök bármilyen segitséget és bocsánat ha nem jo helyen érdeklödtem...
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce