Service manuals, schematics, eproms for electrical technicians

PHILIPS D16 SHASSIS 25DC2660-21R SCH

TV - SERVICE MANUAL
Type: (ZIP)
Size
4.5 MB
Page
---
Category
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar philips manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    PHILIPS D-16 D16 SHASSIS 16 25 DC 266021 25DC2660 21R
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Philips 26PFL3404/12 villámlátogatott...
Sziasztok! ISMÉT segítséget kérnék. Ennek a szegény "villámlátogatott" tévének a rajza (tápegység) nincs meg valakinek? Lehet ez(is) csak bénaságomnak tudható be, de én nem találom sehol... csakúgy mint a hibát, mely hiányos feszültségekben mutatkozik meg. Köszönettel: Z.
Philips21PT1654/48 SL9.2E AA Egy kis füst...
Üdv az Uraknak. A hiba egyszerű -nek tűnik-. Sorvég kicsatóló összeégett egy mellette lévő csillapító ellenállattal. ("Rabbi! Nem a vajas felére esett a kenyerem, pedig Te azt mondtad, mindig arra esik. Mond Kohn, BIZTOSAN A JÓ FELÉT KENTED MEG?). Szóval TERMÉSZETESEN a kondi feliratos fele égett meg! Sebaj, mire való a tanya? Szóval mostanában sikerült pár rajzot kinyomtatnom, legutóbb is egy Philipshez, (ugye mondanom se kell, kézbe se vettem, olyan megnyugtató volt a tudat, hogy van, egyből megjött az önbizalmam és rajz nélkül megjavszereltem - no jó, elővettem fél év után a szkópot-,) szóval, NEM ENGEDI A SZÁMÍTÓGÉPEM MEGNYITNI A RAJZOKAT, SE LETÖLTENI, a fiam meg nincs itthon, hogy megoldja. Nos kellene nekem a z R3407 és a vele egy ponton közös C3406 (vagy2404?, nem egyértelmű a feliratozás) értéke. HELP!
Philips 32pfl5604h/12 nem ad képet
Kedves kollegák. Sgítséget szeretnék kérni a fent említett tv-vel kapcsolatban. A tünet a következő: Bekapcsol háttérvilágítása van,viszont fekete marad a kijelző. A kijelzőt meghajtó részen van 1 ic ami nem akar tápot csinálni a kijelzőnek. BD8162EKV Ez az ic csinálja a kijelző meghajtásának a tápot,van esetleg ötletetek miért nem akar elindulni? Az alaplapon végigmértem a doksi alapján a tápokat azok rendben vannak. Ha esetleg valaki tudna tanácsot adni megköszönném. Üdvözlettel Tams
Televisor Philips 32PFL3605/77 enciende realiza un pantallazo parpadea y pantalla queda oscura
Estimados.

El Televisor Philips 32PFL3605/77 LCD tiene una fuente Philips A961A la cual al cunectar el 220v  se quema el fusible . Se procede a controlar la placa  de la fuente y se reemplazo el mosfet  Q602 (transistor en corto), el ic que controla la tensión de entrada (HS01G)  y también se cambio el fusible .
Luego de reemplazar estos componentes se realizo una prueba y el tv encendió, realizo un pantallazo y luego comenzó a parpadear y se se apaga la pantalla. Midiendo tensión en la salida para las lamparas  en los conectores CN2 y CN3 , al presionar el boton de encendido, la tensión es de 97V, el led testigo de la fuente prende y luego comienza a mermar su intensidad lentamente hasta apagarse, la pantalla parpadea y al cabo de unos segundos la tensión en los conectores CN2 y CN3 queda en 18v y la pantalla queda oscura . 

Me pueden ayudar en la reparación , para determinar cual sera el problema que hace que la tensión no se mantenga fija.!
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce