Service manuals, schematics, eproms for electrical technicians
SONY KV-DR29M39
Type: 
(PDF)
(PDF)Size
20.2 MB
20.2 MB
Page
234
234
Category
TV
SERVICE MANUAL
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Advertisements
Document preview [1st page]
Click on the link for free download!
Document preview [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
SONY KVDR29M39 KVDR 29 39 KV DR29M39 KV-DR29M39
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Jó estét mindenkinek!
Ebben egy BE4A sasszé van.Nem üzemel.A táp működik. Indításnál egészen az S2000 bázisáig megjön a meghajtó jel.A kollektoron megvan a táp,de meg se nyekken.Még egy árva impulzus se látszik rajta.
olyan mintha nem nyitná ki a tranzisztort.
A led 4-et villog.
Zárlatot nem találtam.Próbáltam bele függ íc-t sortrafót,S2000-t.
Most töltöttem le hozzá rajzot,hátha abból holnap okosabb leszek.
Van egy másik ilyen sasszéval szerelt tv nálam,azon meg csak színjel van,nincs Y-JEL.Abból próbáltam át a dolgokat.Még azt nem néztem.
Nagyon jól jönne a segítség,hogy ne körözzek fölöslegesen.
Üdv.
dínó.
Üdv!
Tudnátok segíteni?
Hiába kapcsolom ki a DEMO-t, visszakapcsolódik.
Mit lehet ilyenkor tenni?
Kösz
Tudnátok segíteni?
Hiába kapcsolom ki a DEMO-t, visszakapcsolódik.
Mit lehet ilyenkor tenni?
Kösz
Sziasztok
Bejött ez a SONY KV-29LS60K tipusú készülék. A hiba a következő: Bekapcsolva megy "kb"15-percet,relé kattan 2-villogás a leden. Főkapcsoló ki majd vissza , azonnal indul , de csak 5 percig,harmadszor már csak 1 perc , hibajelzés mindíg 2 villogás.A tunert kocogtatva kontakt hibára lettem figyelmes."tipikus SONY hiba".Emiat letílthat-e a készülék? Mi a 2-es hibakód? "ma egész nap ment hibátlanul a TV" Köszönöm előre is a segítséget!Nem kontakthiba.
polonkay
Screenshots of problem here in the post.
Picture of screen with both cables to panel from TCON connected, and the other is with one side disconnected.
I have read the cables from the TCON to the display loosen up on the end to the panel. I believe as I am working on moving the cables around, the picture is improving
and getting clearer. So I think thats the problem. Someone mentioned using tape over them to hold them to the panel better. I have not taken the metal frame off to
look at them, but there is a narrow gap where I read some people stuff cardboard in there to press down on them better.
Has anyone ever seen this issue and come up with a good way to resecure the cables?
Picture of screen with both cables to panel from TCON connected, and the other is with one side disconnected.
I have read the cables from the TCON to the display loosen up on the end to the panel. I believe as I am working on moving the cables around, the picture is improving
and getting clearer. So I think thats the problem. Someone mentioned using tape over them to hold them to the panel better. I have not taken the metal frame off to
look at them, but there is a narrow gap where I read some people stuff cardboard in there to press down on them better.
Has anyone ever seen this issue and come up with a good way to resecure the cables?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce