Service manuals, schematics, eproms for electrical technicians
SONY KVM2181D CH BE4 0
Type: 
(ZIP)
(ZIP)Size
324.0byte
324.0byte
Page
---
---
Category
TV
EPROM
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
SONY KVM-2181D CH BE-4 KVM2181D BE4 KVM 2181 BE
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Üdv.Mindenkinek,
A fenti készüléket hozta egy ismerősöm ma. ( LB 31/ LB36 chassis, LGP42-13PL1 táp )
Mivel holnap elutazunk próbáltam gyorsan túllendülni rajta, de a fenti jelenségen kívül nem találtam még más hibát.
A LED megható fesz. 100 és 125V között lassan ingadozik (157,5V helyett).
Az kondik jónak látszanak (mérve is)a táp többi része kifogástalan.
Szervízkönyvet találtam róla de abban pont a tápról nincs bővebb leírás.
Van valakinek ezzel a készülékkel már ilyen tapasztalata?
Esetleg a tápról bővebb leírása?
Csatolok néhány képet a könnyebb beazonosításhoz.
Minden segítséget előre is köszönök.
Üdv.
Tibor
Sziasztok!
A fenti gépben lámpát cseréltem. Bekapcsolás után a ventilátor felpörög, a " lamp/cover " pár másodperc múlva felvillan. Majd 25-30mp múlva folyamatosan világít, a stby lámpa villog. Mit nem végeztem el? Az ajtó érzékelő működik, máshol kapcsolót nem találtam.
Helló!
Ezzel a készülékkel időközönként romba döntöm szakmai tudásomat. A hibája, hogy bekapcsoláskor (nem mindig) Sípoló hanggal indul. Ezt melegedés hatására abbahagyja ill. ha újraindítom. Sok elkó és forrasztás után sem lett jó. Elegem van belőle. A hiba biztosan a függőlegesen álló tuner+ digi modulon van. Ezt cserével be tudtam azonosítani. Ilyet keresek. Biztosan van vkinek egy csőhibás készüléke amibe jó még ez.
Köszi, üdv.: Ízirájder
Screenshots of problem here in the post.
Picture of screen with both cables to panel from TCON connected, and the other is with one side disconnected.
I have read the cables from the TCON to the display loosen up on the end to the panel. I believe as I am working on moving the cables around, the picture is improving
and getting clearer. So I think thats the problem. Someone mentioned using tape over them to hold them to the panel better. I have not taken the metal frame off to
look at them, but there is a narrow gap where I read some people stuff cardboard in there to press down on them better.
Has anyone ever seen this issue and come up with a good way to resecure the cables?
Picture of screen with both cables to panel from TCON connected, and the other is with one side disconnected.
I have read the cables from the TCON to the display loosen up on the end to the panel. I believe as I am working on moving the cables around, the picture is improving
and getting clearer. So I think thats the problem. Someone mentioned using tape over them to hold them to the panel better. I have not taken the metal frame off to
look at them, but there is a narrow gap where I read some people stuff cardboard in there to press down on them better.
Has anyone ever seen this issue and come up with a good way to resecure the cables?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce