Hello
I have on my table this sony kdl32ex600 with backlight issue. It's a common failure of this psu but i do not find any part faulted on this board.
The schematic it is almost the same, with minor differences with GE3B found at page 56 on this service manual:
https://elektrotanya.com/sony_kdl-32ex600_kdl-40ex600_kdl46ex600_chassis_az1-k.pdf/download.html
Uploaded only the page 56 from this sm to easing the search.
The red led it's flashing 2 times, meaning psu faulty. Indeed the led backlight does not light.
With the PSU outside of the tv, just with one resistance of 180ohm between standby ( pin 1 3,3V on connector CN6150 ) i get this values
on in:
starting with pin 1
1 +3,3V ST-BY
2 +3,3V AC_OFF_DET
3 +3,3V POWER_ON (with resistance 180ohm between pin1 and pin 3)
4 +12,56V AUDIO_12V
5 0V AUDIO_12V_GND
6 0V REG_12V_GND
7 0V REG_12V_GND
8 +12,6V REG_12V
9 +12,6V REG_12V
10 +0,1V BL_ERR
11 +3,3V BL_ON
12 0V DIMMER
13 0V DIMMER_DC
14 0V T-CON_Vcc_12V
15 0V T-CON_ON
All measure done at secondary ground point C6800 GND as reference.
Meanwhile, the led connected to CN6800 will remain with no light at all. The CN6800 will deliver positive 91V.
The negative branch will deliver at CN6801 ( both pin1 & 2 ) just -1V.
In the training manual found always in here at
https://elektrotanya.com/sony_kdl-32ex600_40ex600_46ex600_chassis_az1k_training%20manual.pdf/download.html
at page 56 will say "SHORT" at pin 12 DIMMER for testing the PSU, always with pin 3 POWER_ON connected to 3,3V ST-BY - pin1.
If i'll put a 180ohm resistance between GND and pin 12 DIMMER, then the tension on CN6800 will rise to +179V and the negative from the CN6801 will rise to -5V, the backlight led will light very very weak.
All tension from CN6805 will remain the same, except the BL_ERR will rise from +0,1V to +1,1V.
With only power_on pin 3 shorted by 180ohm resistance to the pin 1, i get this weak oscillation at emiter of Q6816 + Q6817
[URL=https://picturepush.com/public/16067400][IMG]https://www1.picturepush.com/photo/a/16067400/640/diverse/Q6816Q6817.jpg[/IMG][/URL]
With pin 12 DIMMER shorted ( always by a 180ohm resistance ) at GND, the oscillation will change from 250khz 1,6vpp to almost 70khz at 0,81Vpp. as below:
[URL=https://picturepush.com/public/16067401][IMG]https://www1.picturepush.com/photo/a/16067401/640/diverse/20181117-175255.jpg[/IMG][/URL]
Already checked the capacitors C6828 / C6830 together with D6805 / D6806.
Also checked the L6800 ( trafo ) and i've get 5,5mH instead of 5mH, i think it's ok.
All fuse checked, ok.
Q6814 and Q6801 tested under mosfet tester, ok.
[url=https://picturepush.com/public/16067402][img=https://www1.picturepush.com/photo/a/16067402/220/16067402.jpg][/url]
IC6800 & IC6801 gave +9V and respectively +2,49V
Already checked various components all over the board, i am out of ideas.
Any idea or help would be apreciated.
Üdvözletem a Mestereknek!Kaptam ajándékba a fent nevezett tv-t ,nemrég volt javitva , "lapos tv" váltotta fel a helyét az eredeti tulajdonosánál!Sajnos nem sokáig örülhettem neki mert 5 percnyi filmnézés után a vizszintes képméret egyszer csak lecsökkent, hirtelen ,összeugrott a kép ,majd eltünt teljesen ,és felszált az üzemi füst.A tv alaplapján csak a 1-653-363-22 számsort találtam . Kutakodtam a neten és azt találtam hogy G3 saszira épül fel ,ilyen rajzot viszont nem találtam ,igy a Tanyán lévö G3E rajz alapján áltam neki a javitásnak. A sorvégfokozatban BU 2520 DX tranzisztor volt nemrég beépitve ez zárlatos lett,a rajzon 2SD1878-CA van feltüntetve.Mivel ilyen tipusu tranzisztorom nem volt BUH 515 D tipust tettem a helyére,mielött bekapcsoltam volna ellenöriztem a C801-33mikro/160 volt,R806,R803,C802,R811,R808,R809 pozicioban levó alkatrészeket .Bekapcsolva a tv normálisan müködik ,kép ,hang,szin rendben.Bekapcsolás pillanatátol mértem a sorvégtranzisztor hütöborgáján a hömérsékletet,1 órai müködés után a hömérséklet 54 fok,ennél jobban nem emelkedik.Az lenne a kérdésem hogy ez a höfok megengedhetö e hosszu távon ? A sorvégfokozatot meghajtó driver tranzisztor kollektorán 100 pp nagyságu jelet mértem, rajz szerint viszont 170 pp kellene ..Nem szeretném ha elfüstölne ezért megvárom a véleményeiteket ezzel kapcsolatban ,és elöre is köszönöm üdv dddemeter!
.
Hello
The TV does not show any sign of life , I started the troubleshoot as this , no power Led, no reaction when pressing the power button.
I checked the Power coming out from the power supply, the 3.3V_standby is correct and steady, then I checked the 1.2V_standby produced by IC6001 which Is good as well.
So I decided to control the main IC , IC4000 , he does not output any oscillation on the Xtal, Then I am now bloacked there.
The schematic is downloadable on this website , the schema is weird because the processor is not represented with any Xtal output, but obviously it has one.
Thanks you for your hint and help.
Sziasztok!
A fent nevezett tvének nincs háttér világítása, a táp rajzán nem találtam meg az inverter részt. A fetek rendben vannak, diódák is. Mi hajtja meg az inverter részt, vagy erről a részről rajzot tudna valaki?