Service manuals, schematics, eproms for electrical technicians

STATRON TG30-1

METER - SERVICE MANUAL
Type: (ZIP)
Size
8.5 MB
Page
---
Category
METER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar statron manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    STATRON TG-301 TG301 TG 301 TG30 TG30-1
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant METER forum topics:
Trakis toroid transzformátor javitás (500w)
Tisztelt Fórumtársak, A cimben szereplő toroid megadta magát. Tudtok javasolni valakit aki tisztességgel ujratekerné jóárasitva? Budapest lenne a célszerű nekem.
TR-0469 (EMG 12567) függvénygenerátor hiba (mégsem oldódott meg)
Sziasztok! A fenti programozható függvény/arbitrary generátor ('89-es EMG műszer) bekapcsoláskor (hideg állapotból) az összes kijelző, ill LED elkezd villogni (pedig van vagy 50), úgy 1-2 perc múlva pedig lefagy, vmi értelmetlen kombinációban. Többszöri ki-be kapcsolás után helyreáll és működik. Azt hittem, párától; napon szárítottam 1 napig, azután egyből működött vagy 2 napig, utána ugyanez, pedig száraz idő volt már. Tápfeszek, setup-aksi jó.(van eredeti gépkönyvem, vagy 2 kiló.) Bent olyan 10-12 hatalmas nyák, tele CMOS és TTL IC-vel. Fogalmam sincs, hol keressem a hibát. Örülnék, ha valaki ismerné, vagy javította, esetleg volt EMG-dolgozó. (Nagyon szeretem és jónak tartom a sajnos, néhai EMG műszereit, csővoltmérőm, szkópom is ilyen.) Előre is köszönettel: Szamos
Aoyue 768 hőlégfúvás hiba
Sziasztok! Gondom akadt a szervíz állomásommal, méghozzá a hőlégfúvó részével. Nem fújja, vagyis csak egy nagyon picit a levegőt. Szétszedtem, nem látok hibát, a membránok nem szakadtak, mozognak is rendessen, reagálnak, ha állítok az erősségen. Mi lehet a baj? Erről lenne szó: És egy ilyen dolgozik benne:
Tranzisztor/triak ellenőrző, induktív-kapacitív/ellenállás mérő műszer véleményt szeretnék kérni
Sziasztok, találtam egy kis műszert az e-bay-en. Találkozott vele már valaki, mi a véleményetek? Köszönöm szépen előre is! Szép napot! :help:
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce