Service manuals, schematics, eproms for electrical technicians

VELODYNE SPL-10 CONTROL-PCB SCH

AUDIO - SERVICE MANUAL
Type: (PDF)
Size
162.7 KB
Page
1
Category
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar velodyne manual?
Document preview [1st page]
VELODYNE SPL-10 CONTROL-PCB SCH service manual (1st page)
Preview of VELODYNE SPL-10 CONTROL-PCB SCH [1st page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    VELODYNE SPL-10 SPL10 CONTROLPCB SPL 10 CONTROL PCB
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Honda Jazz autórádió MEGOLDVA!!!
Sziasztok! A következő problémával fordulnék hozzátok. Az egyik barátom Honda Jazz tipusú autójában a gyári fejegységgel adódott problémám. A tipusa: MF9HN08L/MF622RV. Ez egy CD-s rádió. A hiba a következő: minden egyes funkció működik rajta csak a rádió hallott. Nem hangol, nem csinál semmit. Cd és egyébb funkciók mennek rajta. Amit eddig csináltam az a tucatnyi kh megszüntetése. Rajzot nem találtam róla. Itt megakadtam. Ha valaki tud ebben segíteni , hogy merre induljak az ötleteket várom. A segítséget előre is köszönöm: Gábor Minden Segítséget köszönök! Az Egyik 0-ohm os Átrkötés volt szakadt. a tunerben.
Smd mini nyomokapcsolot keresek Pioneer autohifi elölapban
Sép napot kivánok mindenkinek Pioneer DEH 6700MP Cserélni kéne egy barátom auto hifijében az elölapon levö gombokat, de nem találok ilyen tipusut. Kettö külömbözö tipusu van benne Kapcsolási rajzon feltüntetett tipus : CSG1173 CSG1110 Méretei:5.12 X 5.15 X (2.6 magasság gombot beleértve) 3,8 X 2.8 X (2.6 magasság gombot beleértve) Segitségeteket elöre is köszönöm
Onkyo tx-ds575 már nincs hang, de hol volt hol nem :)
Sziasztok! Hozzám került a fent nevezett házi rozi erősitő. Nincs hang a digit bemeneten panasszal, de analog jól működik. Kipróbáltam, csak annyit tettem, hogy a menüben átkapcsoltam a jelforrást, mert egy bemenethez konfigolható, hogy melyik forrást használja. Pl videó2-re kapcsolva optikai, koax1 v 2 vagy video2 analog castlakozókról lehet jelet továbbitani. Kikapcsoltam, hagytam pihenni 1-2 napot, bekapcsoláskor már nem szólalt meg. Se analog, se egyik digit sem. /és azóta sem/ Neten sokan panaszkodnak ilyen hibára, sok helyen a dsp panel eeprom újraforrasztását javasolják. Szétszedtem, már ez az ic volt forrasztva- nem is túl szépen. Átforrasztottam, de nem javult meg. végig követtem az analóg jelet és a digit hangerő szabályzó ic-ig eljut, de belőle már nem jön ki. A tápfeszek rendben +-7,3 (6,8V) 5,18V (5,05V) viszont a vezérlő jelek nincsenek meg. Ic adatlapja: http://www.datasheetcatalog.org/datasheet/MitsubishiElectricCorporation/mXryvxx.pdf Az órajel periodus ideje min 8us aka 125kHz. De sem ez, sem az adat lábon nincs jel. A jeleket a uC adja ki, vagyis adná ki, de itt sincs jel, szkóppal nézve :S Átforrasztottam ezt is, hiába. Ez az ic kezeli a gombokat, vezérli a bemenet válaszót, a hangerő encodert, de ezt mind jól végzi. Az egyik panelen vannak a táp stabilizátor ic-k, némelyiknek 1-2 lába már félig kiforrasztotta magát, újraforrasztottam, hiába. Van valami tippetek mit lehetne még megnézni? köszönöm, Balázs
ECLER NUO 2 (fuse problem)

Hi,

i just checked the service manual of this mix table and I’m questioning myself about the fuse which needs to be used on it as on the schematic I can see 2 fuses but I lost this fuses plastic holder long time ago and now I’m going to receive the new power supply ( FMFONT30C ) which was faulty and I’m going to make it works again but I’m not sure if the fuses plastic holder is using one fuse and you got a spare one on it ( this is what I think by mind but it was years ago ) or it needs to use 2 fuses.
fuse are 500ma 5X20.

you can find the service manual in attached file. ( screen shot ) but the complete service manual can be found on this website too.

thanks for your advise.

regards, 
 

Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce