Service manuals, schematics, eproms for electrical technicians
VESNA 301 ULT47 1971 RUS.
Type: 
(DJVU)
(DJVU)Size
84.3 KB
84.3 KB
Page
1
1
Category
TV
SERVICE MANUAL
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar vesna manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar vesna manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download processing...
Download processing...
- Also known:
VESNA 301 ULT47 1971 RUS. ULT 47
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Dear ppl,
Can anyone please share the firmware file, for this tv?
HDMI inputs, are not working.
Already tried to update the firmware via web (not by USB), but the tv shows that it has the last version already installed!
I guess that one of this versions, should work.
V0000.01.02A.D0827
V0000.01.03A.E0106
Actual intalled version is attached as file.
They say that this TVs uses the same firmware, but i am no sure.
SANYO LCE32IH12
PHILCO PLD3223HI
JVC LT32DR930
Maker: NOBLEX
Model: 32LD860HI
Chassis: MSD1328
Matriz: HISENSE
Remote control: ER-33905
Wifi: DONGLE WFLT01
MainBoard: RSAG7.820.4900
Can anyone please share the firmware file, for this tv?
HDMI inputs, are not working.
Already tried to update the firmware via web (not by USB), but the tv shows that it has the last version already installed!
I guess that one of this versions, should work.
V0000.01.02A.D0827
V0000.01.03A.E0106
Actual intalled version is attached as file.
They say that this TVs uses the same firmware, but i am no sure.
SANYO LCE32IH12
PHILCO PLD3223HI
JVC LT32DR930
Maker: NOBLEX
Model: 32LD860HI
Chassis: MSD1328
Matriz: HISENSE
Remote control: ER-33905
Wifi: DONGLE WFLT01
MainBoard: RSAG7.820.4900
Üdvözlet mindenkinek!
Segítséget szeretnék kérni a címben említett TV-hez.A hibajelenég,hogy párnatorzítása van a készüléknek.Elkókat cseréltem amelyik gyanús volt és átforrasztottam a kritikus részeket.Mit kellene még ellenőriznem,mi okozza a hibát?Előre is köszönöm a segítséget.
Üdv:Mitu
Udv. mindenkinek . A fent emlitett tv tipusnal a tcon modul meghibasodott .Nem kaptam a forfalmazkonal ezt a tipust es megprobaltam behatarolni a modulon a hibat. Egyebkent a modul 320WTC2lv8.4. Az IC15 zarlatos .Az lenne a kerdesem hogy mekkora a valoszinusege hogy a kijelzo is defektes legyen ebbe az esetbe,es az ic 11 mekkora feszt. kellene adjon (nalam 15V).Elore is koszonom a segitseget.
Sziasztok!
Meggyűlt a bajom a fent említett Grundig TV-vel. CUC7350 sasszival van szerelve. OSD kijelzés csak AV1-en van, AV2-őn ill. RF-en nincs.
RF-en nincs zaj (hangyaháború), csak sötét képernyő. Állítólag egy tanítható távirányítóval összekuszálták a service menüjét. A 24C04
eepromot kiolvasva a programozó hibásnak találta, csak a fele memóriaterületet látta. A tanyáról letöltve az eepromtartalmat egy újba
beégetve a hiba továbbra is fennáll.
Lehetséges, hogy a processzorpanelon található két processzor ZC411867 ill. MC68HC705J2P is sérülhetett?
Segítségeteket előre is köszönöm.
Tisztelettel: Juhász Gábor
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce