Service manuals, schematics, eproms for electrical technicians

VESTEL VR54TF-2145

TV - EPROM
Type: (RAR)
Size
776.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar vestel manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    VESTEL VR54TF2145 VR 54 TF 2145 VR54TF
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
17PW07-2 Vestel táp halott
Sziasztok!

Fent nevezett tápegységű készülék (SHARP LC40LE510E) nem csinál semmit.
Nem is tud, mivel a táp mindkét biztije F100, F101 elvillant. A PFC árammérő söntje R109 0,22 Ohm szakadt, és a +400 V bus kondiknál a fólia is égett. Tehát valami erősen ette a villanyt
Eddig semmi más zárlat jellegűt nem találtam. (FET-eket nem szedtem ki, ott még lehet szakadás). A hibákat megszüntettem.
Most viszont a 400 V az 327 V (úgy gondolom, míg STBY van, ez OK, bár nem tudom).
A rajz kissé átláthatatlan számomra (nagyon széttagolt és nem kereshető a PDF), valamint (jó)pár alkatrész nincs beültetve.
A 4.25 V STBY_1 villany viszont 0,5 V.
Azt gondolom, a STBY-nak akkor is lennie kellene, ha a MainBoard-al nincs összekötve, bár az IC302 opto körüli rész mágikus szerkezet.
A STBY szekunder része nem zárlatos, mégis "csuklik" az FDSL321 (IC301). Ezért arra gondolok, hogy az OVP szólal meg.
"4.4 Over Voltage Protection (OVP) : In the event of a malfunction in the secondary side feedback circuit, or an open
feedback loop caused by a soldering defect, the current through the opto-coupler transistor becomes almost zero
(refer to Figure 5). Then, VFB climbs up in a similar manner to the over load situation, forcing the preset maximum current
to be supplied to the SMPS until the over load protection is activated. Because excess energy is provided to the output,
the output voltage may exceed the rated voltage before the over load protection is activated, resulting in the breakdown
of the devices in the secondary side. In order to prevent this situation, an over voltage protection (OVP) circuit is
employed. In general, Vcc is proportional to the output voltage and the FPS uses Vcc instead of directly monitoring the
output voltage. If VCC exceeds 19V, OVP circuit is activatedr esulting in termination of the switching operation. In order
to avoid undesired activation of OVP during normal operation,Vcc should be properly designed to be below 19V."
Nos, a VCC majdnem 20 V-ig ugrik.
Bár a visszacsatoló optót (IC300) sem ellenőriztem még.

Valaki találkozott már hasonló problémával? Kérem segítsen!
Köszönöm:
Péter
Vestel 11AK30-2 opció(Nagypapi jóvoltából megoldva)
Tiszteletem, a Tanyán fórumozóknak! Egy agyhalott készülék feltámasztása után, érdekes jelenséget produkál. Az alaplapon, két AV bemenet van, SCART, és RCA. Értelem szerűen AV1, ill. AV2. Amennyiben engedélyezve van, az AV2. bemenet is, akkor bekapcsoláskor (készenlétből is) megjelenik a kiválasztott csatorna, egy rövid pillanatra, majd átlép AV2-be. Amennyiben, csak az AV1. van engedélyezve, nincs ilyen probléma. TV parancsra, természetesen a behangolt állomások jelennek meg, és gond nélkül működik minden. Kissé zavaró a dolog. Kérem, hogy egy jó ötlettel segítsetek megoldani ezt az anomáliát. Válaszaitokat előre is köszönöm. Üdvözlettel: exGelkás
17MB61-2 VESTEL LCD MAIN 16-ot villog indulás előtt
Sziasztok! A fenti mainnal szerelt lcd tv,táp ( 16PW26-5) javítás után hibátlanul működik. Azt leszámítva,hogy indítás után 16-ot villog a készenléti ledje,mielőtt megjelenik a kép és a hang. Wolf
17PW15-9 Vestel LCD tv tápegység időnként leáll
Sziasztok! A fenti táp időnként leáll. Ha átforrasztom, kb egy napig jó. > *Ütögetésre nem reagál.... > *Van valakinek tapasztalata? Üdv: Wolf
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce