Service manuals, schematics, eproms for electrical technicians

AMSTRAD TVR3 CHASSIS.

TV - SERVICE MANUAL
Type: (DJVU)
Size
106.6 KB
Page
6
Category
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar amstrad manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    AMSTRAD TVR-3 TVR3 CHASSIS. TVR
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
BenQ DV3750 LCD TV Táp nem kapcsol be!!!
Tisztelt tanyalakok! A fenti TV táp FSP320-6F01 Zárlatos volt a 2SK2711 UC3843 ZTX15 0R43 szakadt,kicserélve a+5V van.A többi táp feszültség nem kapcsol be... Mit nézek meg akinek van ötlete ossza meg velem Köszönöm. Kocsis Gy
GoldStar CK-20D10X chassis PC-31A ,tap nem indul st by eg
bekapcsolas utan 2 masodprc a rele kikapcsol , prog (+ -) NEM REAGAL benyomva tartva a 220 as kapcsolot a fo feszultseg meg van , sorba kotot egovel szinten ,a diodarol a testre szinten kikapcsol ,afo feszulltseg normalis es alithato .
Elektronika 450 kis TV csak raszter van
Sziasztok ELEKTRONIKA 450 kis tv nosztalgiából nekiláttam."bevallom őszintén , úgy látszik túl fiatal vagyok a germánium tranzisztorok sajátságos világához, pláne igaz ha az orosz narancssárgára gondolok... Elindult, raszter van hang is csak az alapzaj ami csak az erősítő zaja. Antennát bedugva nem találok állomást. KF hiba lehet, ráadásul az első körökben. Próbából tettem rá egy másik tunert, megfelelő helyeken táplálva, egy kanyi állomás, meg zajváltozás sincs hangoláskor. Az első KF erősítő tranzisztor Emiterén kb 3,7V -t mérek a 8,4V helyett. Cseréltem a GT tranyót egy AF 106 tranzisztorra, nem sok sikerrel.Vannak az orosz csoda vastagréteg áramkörök is... Kicsit nehézkes a javítása, pláne, ha a tunerhez kell hozzányúlni.ott is méregettem, a hangoló feszültség 0-25V a tápja 9,6V. Az AGC áramkörben elkókat cseréltem, hátha az szabályoz le, de sajna nem. Ugyan egyedül itt a Tanyán van rajz , de ha valakinek gazdagabb dokuja , infója lenne megköszönném. Esetleg hasonló típus, amiről lenne valami. Köszi Üdv Szabi
pins labels of backlight driver IC BD94240235
I got a repair of SONY model KD-43X7500H, made in Malaysia, an Android smart LED Tv. The first time I worked on it, was that, it shows the logo SONY for a minute then the backlight turns off but still, you can see the panel's picture working as you can see it's silhoutte. I  managed to re-soldered the two ICs, which are 'square' type SMD ICs with I think, 10 pins on each sides (total of 40 pins) with label BD9424 0235 for each ICs. As I checked on it. there are two ICs to drive the LEDs in an in-line array arrangement), not the common types of backlights scattered all over at the back of the LED panel. I was successful then but just for a few weeks, the same trouble happened again. As I observed it, before the backlight turns off, there's a bit of a dimmer lighting at the right side of the panel screen. I resoldered it the second time and it worked. Now, the third time as a backjob, the panel screen will show the Sony and android letters logo with 'even' lighting behind the panel screen but then, after a few seconds, the backlight turns on with red light indicator blinking 6 times. I hope someone can show me the pin labels of the driver IC. BD9424 023, so I can study how to make some kind of modification, as I suspect, one of the ICs could possibly, already defective.In advance, thank you very much for those who could help. God bless us all.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce