Sziasztok!
16:9-es 66cm-es CRT TV bekapcsolva klattyog a relé, a B+ 145V-rol leesik 130V-ra, a BU melegszik, tehát le van terheve.40W Égôvel stabilan áll a 145V.
Ha kihuzom a Horizontalis elterito tekercset akkor beindul a TV nem melegszik semmi csak akkor fuggoleges vonal van. Ha lecsatolom az E/W tranzisztorra vezeto jelet akkor kb 3cm széles a kép majd 10-15sec alatt ugy felmelegszik a BU250AF hogy kiég. Leszedtem már az eltérito tekercset, de az vizualisan szépen néz ki, de 0ohm-ot mérek (egyszeru multiméterrel).
Amiket már probara csereltem:BU2508AF, meghajtoja BS270, 8.2nF/2kV meg a melette levo nagymeretu kondik, E/W tranzisztor BDW53B, környékbeli elkók, sajnos már vettem uj nagyfesztrafót is.Megmértem egy masik TV elteritojét ott is 0 ohmot mértem ebbôl gondolom az elterito tekercsem is jó.
Most megallt a tudomany..
Sziasztok!
Belefutottam egy 17mb140 main flash hibába. Nem tudtam az eredeti W25Q128 -at törölni, gondoltam hibás - ezért rendeltem kettő újat.
Itt jött a meglepetés: amíg meg nem írom addig működik az erase parancs, legalább fél percig csinálja. De ha rátöltök egy flash tartalmat, a törlés egy pillanat alatt lefut, és minden adat megmarad.
Ha jól értem az adatlapja szerint be kellene állítani egy státusz regiszter bitet hogy engedje a cip erase parancsot.
"The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write Enable instruction must be executed before the device will accept the Chip Erase Instruction (StatusRegister bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the instruction code “C7h”or “60h”
Két programozóm is van, egy EZP2010 és egy CH314. Egy kis segítséget kérnék, hogyan tudnám engedélyezni a törlést.
Eddig a W25Q16, 32 és 64 SPI nem produkált ilyen jelenséget...
Előre is köszönöm!
Joco
UPDATE:
Note: This Model and CUC220, CUC720 almost identical
My family b. this TV in 80'
And worked ~15 years
In 90' Black screen ... with Pot. in 100% Brightness, Contrast.
In the end 90' puff doesn't work at all.
Someone try repair but ... the same black screen.
They reported ... try fix and get > Brightness
In past 6 months, I repaired and new life come from the set, but now we get too much Brightness
In your opinion ... the person try Adjust ... fix what?
ABL - Automatic Brightness Limiter setup, regul.?
R2533 R2538?
Thank you for your comments, info.
Ruy
Please your comments:
Brightness and Colour Pot. -> OK
But Contrast Pot.: I can' rise ... NO FOCUS and
washed out -> I only see a Blank RASTER.
Best Regards,
Ruy
__________________________________________________________________________________
ORIGINAL / PAST MSG
Hi,
Super Color A 7100
The other sub-models in pag.1 - pdf
right bottom
elektrotanya.com/grundig_cuc120.pdf/download.html
The screen is black ... and we notice from time to time (when the image is very brig.) some small part of image.
Very few dots.
I tested the G1 2X V, G2 5XX V, Heather - G and J Volts in the neck of Cinesc.
Power Supply I tested +A 115 V, +C 200 V , +B 12V, +M 19V
In Pag. 6 - SSB and SB? T2533
Thank you,
Ruy
__________________________________________________________________________
Work with servers - OpenBSD, NetBSD, FreeBSD, Linux.
Love Oscilloscope :-) , Repair, Satellite Dish, Multimeters.
Have a Big Satellite Dish farm.
Szép napot mindenkinek!
Meghibásodott az ALIEN típusú tv-m, 11AK30A4 alaplapon. Megette a BU808DFI-t. A sorkimenő trafót is kiszereltem.
Segítségeteket kérem a trafó beazonosításához, és az alkatrészek beszerzési lehetőségről.
Köszönöm. Laci