Sziasztok!
Egy ismerősöm megkért, hogy az általa felújítandó R646U rádiót keltsem életre.
Ő már a kapcsolósort rendbe tette.
Szerintem valamit elköthetett, mert az oszcillátor nem akar indulni.
Sajnos pontos rajzot erről az altípusról nem találtam.
Legjobban az R646N (Velence) típussal egyezik, de pont a kapcsolósornál lévő elrendezés más.
Az ECH81 keverő-oszcillátor csövön a DC szintek szerintem rendben vannak, a KF működik.
Mellékelek egy képet a kapcsolósor alatti modulátor - oszcillátor tekercsek és trimmerek elrendezéséről.
Ha lenne egy pontos kapcsolási rajz erről a típusról, akkor lényegesen könnyebb dolgom lenne.
Kumi
Sziasztok
A keresztfiamnak van egy Technics SA-EX140 típusú erősítője.
Az a probléma jelentkezett nála, hogy ha kb 20%-nál jobban felhangosítom, akkor bekapcsol a védelme, és leválasztja hangszórókat. Ez nem jön helyre ki-be kapcsolással sem, csak áramtalanítás után.
Nem hangszóró, azok impedanciája nem változott, azon a hangerőn szépen is szólnak.
Kipróbáltam hangszórók nélkül is, ugyanaz a jelenség.
Bizonyso hangerő felett röviden elindul a hűtőventillátora, abban a pillanatban kattan a relé és kiold.
Felfújódott kondit nem láttam benne. Megtaláltam itt a tanyán a szerviz-könyvét, de hátha valakinek van ezzel tapasztalata.
Minden jót,
János
Sziasztok!Üdül nálam egy AIWA 3lemezes mini hifi.Model no:cx-ns32hr.Ami gond van vele,lemeztálca behúzás után mind a három lemezhelyet próbálja beolvasni,de a lemez forgató motor csak 3-szor pördít,közben a fej fókuszál,de nem látom jelét annak se,hogy menne a lézer(nincs fénye)Mind a három pozícióban ezt csinálja,és kész,utána már csak kiadatni lehet vele,nem próbál újra olvasni.Szerintetek mit érdemes még megnézni rajta,mert szerintem fejes!Köszönöm mindenkinek a tippeket,ötleteket előre is!
I greet you! I would need the scheme of this "vintage" amplifier that needs to be "restored". The problem is that in the prefinal and final floor I have many "fried" resistors well, their value cannot be identified.I replaced the defective transistors: 2SC1509, 2SA777,2SB690 and 2SD 796 (each 2 pcs.) and the electrolytic capacitors adjacent to them. I could not go further because of the carbonized resistors that I do not know their value (I can only guess that they are values small, in the order of ohms). The schematic diagram I downloaded, from the address received by the kindness of a colleague is not complete - it is a single page (missing Q29-Q30-Q31-Q3 and resistors R115-R116-R117-R118 which are completely carbonized, at other resistors I could see their value).Thanks in advance!
Finally, I found the missing part
If stuck in the repair and you ask questions, please do it as follows: - Details: Give the exact model number of your device and the chassis ID (if there is). - If possible, please attach pictures of the appliance. - Anamnesis: Write down the exact symptom. If hard to describe the symptom, it is difficult to verbally defined clearly, attach pictures or sound of the phenomenon! - Tell what was you have done so far: search contact error, which parts has examined or changed yet, etc... The incorrectly named topic suspended and will be deleted after 48 hours! Suspended state while others are not able to comment until you correct the address. Subsequent repair of the defective title (within 48 hours) by clicking on the "Edit" tab can be carried out.