Service manuals, schematics, eproms for electrical technicians
JVC AV-28WR2EK
Type: 
(RAR)
(RAR)Size
1.2 KB
1.2 KB
Page
---
---
Category
TV
EPROM
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar jvc manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar jvc manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download processing...
Download processing...
- Also known:
JVC AV28WR2EK AV 28 WR EK 28WR2EK AV-28WR2EK
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Sziasztok!
Ilyet keres egy ismerősöm!
"bekapcskor nagyon csikos vízszintesen meg kb 10cm-es sávok függölegesen,de fél perc után rendbe jön a kép(tulaj szerint melegedésre ujra előjön ez a hibajelenség. Átvizsgálás után a digitpanelre gyanakszom. Hol lehet ilyet beszerezni és mennyiért.Van-e valakinek eladó?vagy javitható-e a panel?.már 2 db is van itt ezzel a hibával. "
Lehet javítani vagy van valamelyikőtöknek netán?
Hűtésre, melegítésre semmi változás.
Újnak amúgy horror ára van :(
Üdv:
Pityesz
Jó napot mindenkinek!
Olyan problémám lenne a fent említett tv-vel, hogy nincs rajta hang hiába állítom a hangerőt! Az aki javította előttem cserélte a végfokot, és egy napig volt rajta hang, azóta nincs! cseréltem a végfokot én is (TDA2615) Előtte ellenőriztem a tápfeszültséget hangszórókat, és minden rendben van! Esetleg valakinek valami infója, hogy mi lehet a probléma?? Talán eeprom?
Üdv mindenkinek.Stevepapa vagyok,kaptam a fent nevezett tv-t.Nem volt benn sortranyó.Át mértem,kondiztam és tettem bele egyet ami kb 5mp-ig élt.Ekkor bekapcsoltam a szkópot,minden
rendben volt,szép hajtójel,sima tápok.A bajok
akkor jöttek mikor rákötöttem az izzót.A 136v-os táp igen furcsa jeleket produkált,ami ráült
a 14v-ra is meg a sorjelre is.Remélem valaki már találkozott ilyen hibával,előre is köszönöm.
JVC AV-21FMG4G Chassis SCW-1362A CRT TV blinks continuously after three failing power on attempts.
According to the customer, the upper portion of the screen started shrinking with horizontal lines, then ended with a single thin horizontal line.
This suspects the vertical drive section to be problematic. No vertical output though vertical in put is OK. After conducting an ESR check for capacitors in the vertical section, C428 (100uF 35V), connecting VCC1 with Pump-up pin # 3 of the IC, it measured 1200pF. It was replaced but still no vertical output. So changed the vertical IC401 (TDA78040), and the output appeared, but still blinks after three failing start-ups. I, m suspecting the corrupt EEPROM data.
CPU: TDA11010H / N1D00
EEPROM: 24C16A
Any one with EEPROM dump for this model or any help please?
According to the customer, the upper portion of the screen started shrinking with horizontal lines, then ended with a single thin horizontal line.
This suspects the vertical drive section to be problematic. No vertical output though vertical in put is OK. After conducting an ESR check for capacitors in the vertical section, C428 (100uF 35V), connecting VCC1 with Pump-up pin # 3 of the IC, it measured 1200pF. It was replaced but still no vertical output. So changed the vertical IC401 (TDA78040), and the output appeared, but still blinks after three failing start-ups. I, m suspecting the corrupt EEPROM data.
CPU: TDA11010H / N1D00
EEPROM: 24C16A
Any one with EEPROM dump for this model or any help please?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce