Service manuals, schematics, eproms for electrical technicians
JVC AV-32F802
Type: 
(RAR)
(RAR)Size
7.6 MB
7.6 MB
Page
---
---
Category
TV
SERVICE MANUAL
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar jvc manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar jvc manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
JVC AV-32F-802 AV32F802 AV 32 802 32F802 AV-32F802
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Tisztelt kolléga urak!
Segítségre szorulnék a fentiekben említett tv miatt.
A jelensége hogy euroscart csatlakozóval megy a médiaboxról és az lenne a hibája hogy elmegy a kép,az euroscart mozgatására visszajön de de kisidö múltán ismét elmegy a kép.Én euroscart aljzatra gondoltam volna de mivel két aljzat van mendkettőnél ezt csinálja,sima koax bemenetén pedig a kép alja ugrál,de nem mindig az sem.Szerintem érintkezési hiba lehet csak nemtudom hol kezdjem el a keresést.Ha találkoztatok már ilyen jelenséggel megköszönném a segítségetek.Sajna elég kevés tvt javítottam még és kezdő vagyok benne.Köszi Mindenkinek.
Üdv:Tibi
Sziasztok.
A fenti tv-vel közdöttem.
Minden rendben van vele elvileg ha a menü gombot megnyomom a távon rendesen bejön a menü.
Ha itt lépni akarok bármerre kilép a menüből vissza a tv-hez.
Így nem tudok gyári beállítást se csinálni meg igazából semmit.
Epromra gyanakodtam, kivettem tettem bele üreset, így el se indult.
Tartalmat nem találok hozzá.
Szervíz manuál szerint FT3 sasszi.
Esetleg volt már ilyen hiba valakinél?
Merre tovább?
Köszönöm előre is.
JVC AV-21FMG4G Chassis SCW-1362A CRT TV blinks continuously after three failing power on attempts.
According to the customer, the upper portion of the screen started shrinking with horizontal lines, then ended with a single thin horizontal line.
This suspects the vertical drive section to be problematic. No vertical output though vertical in put is OK. After conducting an ESR check for capacitors in the vertical section, C428 (100uF 35V), connecting VCC1 with Pump-up pin # 3 of the IC, it measured 1200pF. It was replaced but still no vertical output. So changed the vertical IC401 (TDA78040), and the output appeared, but still blinks after three failing start-ups. I, m suspecting the corrupt EEPROM data.
CPU: TDA11010H / N1D00
EEPROM: 24C16A
Any one with EEPROM dump for this model or any help please?
According to the customer, the upper portion of the screen started shrinking with horizontal lines, then ended with a single thin horizontal line.
This suspects the vertical drive section to be problematic. No vertical output though vertical in put is OK. After conducting an ESR check for capacitors in the vertical section, C428 (100uF 35V), connecting VCC1 with Pump-up pin # 3 of the IC, it measured 1200pF. It was replaced but still no vertical output. So changed the vertical IC401 (TDA78040), and the output appeared, but still blinks after three failing start-ups. I, m suspecting the corrupt EEPROM data.
CPU: TDA11010H / N1D00
EEPROM: 24C16A
Any one with EEPROM dump for this model or any help please?
Sziasztok!
Ehhez keresnék tartalmat, az eredeti ic tartalma sérült, újra írás egy másikba lenne a a megoldás.
Köszönettel : Laci
Ehhez keresnék tartalmat, az eredeti ic tartalma sérült, újra írás egy másikba lenne a a megoldás.
Köszönettel : Laci
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce