Sziasztok
Van nekem egy ilyen régi rádióm, ami feladta a harcot.
A kijelzője össze vissza világított.
Felpuffadt kondi nem volt ugyan benne, mert abban a korban készült amikor még nem puffadoztak a kondik,
hanem csak szépen kiszáradtak az idő múlásával.
A táp részben kicseréltem a kondikat, ám, bevallom, valamit rövidre zártam (a harisnyával) és kisült valamelyik kondi.
Két ellenállás elszállt, R801 és R802.
Színkódjukat nem tudtam értelmezni (egy csík eltéréssel egyformák), de pótoltam őket két 22ohmos ellenállással.
( Fehér, Piros, Fekete, Fekete, Barna v. Ezüst )
Első sorban ha valaki tudna segíteni egy SM-el, rajzzal, hogy megtudjam a két ellenállás pontos értékét.
Megoldás:
R802 = 10 ohm
R816 = 18 ohm
Kisebb probléma, hogy nem tárolja le az állomásokat (csak addig tárolja amíg ki nem kapcsolom)
Memória akku rendben, a táphiba előtt működött a tárolás.
Megoldás:
A programok elfelejtéséért valószínűleg az MN1203, ma már őskövületnek számító Statikus RAM lesz a felelős.
Köszönöm.
Given:
Victor TT-71, neon lamp does not light, speed is lower than normal. This is subsequent some short circuit the owner does inside the device. No further details.
I found out the VICTOR QL7 have the same motor driver amd I downloaded the service manual that I attached here in case this manual is not already uploaded.
Looking at the diagrams I found out that at TP3 (same with pin5 of IC803) instead if that rectangular signal, I have nothing but 5VDC and a negative or positive short spike whenever I'm starting or stopping the motor and
Under the circumstances I suspect IC803 is defective. The bad thing, IC803 is NPC SC8043. Also I wonder if the crystal is fine (except that I wonder what can be wrong with a crystal after some short circuit).
Does anybody have any more suggestion?
Also, where can NPC SC4043 be sourced? Also, a crystal 9.054MHz?
Thanks in advance,
Corneliu
Hy!
Van nálam egy JVC center.Bekapcsolás után néhány másodperccel kikapcsolt. A végfok melletti tranyó lábainak a forrasztása repedt volt.Ahogy mozgattam, le is kapcsolt a védelem.Viszont, ha feszesen tartottam(forrasztáshoz nyomtam a lábait), akkor működött rendesen, hang is volt. Megforrasztottam, zárlat sincs, mégsem szól azóta. Viszont nem is kapcsol ki.A kettős táp: +-35V megvan a végfokokon(2db TDA7295), viszont a GND nincs, pedig az adatlapja szerint kellene.De lehet, hogy más a rajz.Ezért is kellene a gépkönyve. Van még olyan probléma is vele, hogy halkításkor is hangosodik. "Örökforgós" gombja van. Ha gyorsan tekerem, akkor le lehet halkítani.És még ami érdekes, hogy a trafónál van 3 bizti. Egy a trafó elött, 2 utána. Viszont az egyik hozzá sem ér a foglalathoz(ki van tágítva duplájára).Amiket találtam hasonló gépkönyvekben, mindkét bizti kell a működéshez.Ez meg anélkül is megy.Ezért is jó lenne legalább a táp meg a végfok rajz.
Tehát: 1.:nincs hang mióta megforrasztottam(viszont nem kapcsol ki), 2.:hangerő gomb bedilizett, 3.:trafónál 3. bizti mi lehet?
üdv: Hege
Sziasztok!!
Van valakine rajza ?
nem is tudom honnan kezdjem,nehezebb javitani mint egy TV-et,STBy nem mukodik,a digital gombok :TUNER,AUX,CD,CASETOFON,le van blokalva, csak a CD-en van kigyulva a piros led.A CD-rom eject gombja mukodik,a casetofon mindegyik gombja mukodik azok is digitalisak.
HANG NINCS.
koszonom