Service manuals, schematics, eproms for electrical technicians


Type: (PDF)
9.0 MB
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar the manual?
Document preview [1st page]
THE HARMAN KARDON HK440VXI service manual (1st page)
Preview of THE HARMAN KARDON HK440VXI [1st page]
Click on the link for free download!
Document preview [2nd page]
THE HARMAN KARDON HK440VXI service manual (2nd page)
Preview of THE HARMAN KARDON HK440VXI [2nd page]
Click on the link for free download!
Please tick the box below to get download link:
  • Also known:
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • Please take a look at the below related repair forum topics. May be help you to repair.
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
STK3102II-STK3102III helyettesíthető-e vele?
Sziasztok! Van egy Marantz Pm-64 típusú erősítőm. Kiment belőle az STK3102IIA fél oldala. Ki kellene cserélnem. Ilyen stk-t már nem találok, de van helyette STK3102III. Helyettesíthető vele? Előre is köszönöm.
Trio-Kenwood: KR-3010 [Radio] S.N.962845 / Does not work, the final floor and prefinal floor defect with many burned component/

I greet you! I would need the scheme of this "vintage" amplifier that needs to be "restored". The problem is that in the prefinal and final floor I have many "fried" resistors well, their value cannot be identified.I replaced the defective transistors: 2SC1509, 2SA777,2SB690 and 2SD 796 (each 2 pcs.) and the electrolytic capacitors adjacent to them. I could not go further because of the carbonized resistors that I do not know their value (I can only guess that they are values small, in the order of ohms). The schematic diagram I downloaded, from the address received by the kindness of a colleague is not complete - it is a single page (missing Q29-Q30-Q31-Q3 and resistors R115-R116-R117-R118 which are completely carbonized, at other resistors I could see their value).Thanks in advance!
Finally, I found the missing part

If stuck in the repair and you ask questions, please do it as follows: - Details: Give the exact model number of your device and the chassis ID (if there is). - If possible, please attach pictures of the appliance. - Anamnesis: Write down the exact symptom. If hard to describe the symptom, it is difficult to verbally defined clearly, attach pictures or sound of the phenomenon! - Tell what was you have done so far: search contact error, which parts has examined or changed yet, etc... The incorrectly named topic suspended and will be deleted after 48 hours! Suspended state while others are not able to comment until you correct the address. Subsequent repair of the defective title (within 48 hours) by clicking on the "Edit" tab can be carried out.

I tried to change the accuphase T-1000

I tried to change the accuphase T-1000 from 76-90mhz to 87.5-108mhz. Now it shows that it is already 87.5-108mhz, but I still cannot find the circuit diagram of AD9850 + UPC3220
Yamaha R-3 Rádiós erősítő végfokokat mivel helyettesíthetem?
Üdv mindenkinek!

A címben említett erősítőn dolgozok, alaposan szét van bombázva. Kibontottam belőle egy marék hibás alkatrészt, ezeket pótolnám. Leginkább a végfokokkal vagyok bajban, hogy mivel helyettesítsem, mert több helyen olvastam, hogy ajánlatos lenne párba válogatott alkatrésszel dolgozni. (erősítőt még soha nem javítottam ilyen mélységekben) Eredetileg passzolok, hogy milyen végfokokkal szerelték, BD249C/BD250C kombó dolgozott benne, amit utólag építettek bele. A manual 3 fajtát említ beépíthetőnek. 2SC3181/2SA1264 kombó, beszerezhető, de szerintem párba válogatásra nincs lehetőség.
Kereszt referencia katalógus "hozza" a 2SA1186/2SC2837 kombót, ami a hq-ban kapható is, párba válogatva. Ezzel a párossal vajon pótolható?

Köszönöm mindenkinek előre is a segítséget.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce