Service manuals, schematics, eproms for electrical technicians
USSR ORLENOK 605.
Type: 
(DJVU)
(DJVU)Size
170.7 KB
170.7 KB
Page
4
4
Category
AUDIO
SERVICE MANUAL
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar ussr manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar ussr manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
USSR ORLENOK 605. 605
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Szép napot mindenkinek. Egy JBL boombox 2 1.6MM készüléket probálnék megjavitani. Látszolag egy 8 lábas dc /dc konverternek látszó ic égett el ,ami U14 panel számozással és az ic-n bBDXA felirat látható.Az lenne a kérésem ,kérdésem hogy ha valakinek lenne infoja az emlitett alkatrészről ,kérem ossza meg velem is. Előre is köszönöm.
Hozzám került egy Nikko R400 rádió erősítő.Hibás volt az STK4171X. Cseréltem, de a tápellátásban van hiba. Jól jönne egy rajz, hogy tudjam a feszültség értékeket. Minden ötlet jól jön.
Hello everyone,
I've this speaker model:
RCF art 415-A.
The power supply is faulty, no votltage out to the amplifier.
The Mosfets are blown. I've changed the mosfets and it's driver, and still have a problem.
I tried to switch on but only one of the mosfets gets hot (the one which switches the 310. There are 2 of them - Mos5 in the scheme).
Obviously I turned it off.
1) What causes it to heat?
2) Testing the VCC of the LMC555, it's only 2.7V. When taking it out of the circuit, it's 12VDC! What makes the voltage to drop. Where does the supply of the LMC555 come from? The VCC of the 555 should be around 10V, as compared with a good card.
I've changed the 555, but the problem remained. I've checked the components around, resistors and capacitors, and transistors, and seem to be OK.
4) The VCC of the Mosfet driver is 10V, but should be 12V if compared with a good card.
3) Could the trafo be damaged? Are these parts reliable or may blow up?
4) What is the purpose of the optocoupler in the circuit?
I would really appreciate any help.
I didn't find the 100% schemes for this RCF (400), but found a very similar one (The 600 version).
name and a link here to download the pdf.
DigiPRO600B
https://elektrotanya.com/db-technologies_digipro600b_sch.pdf/download.html
Regards and many thanks
I've this speaker model:
RCF art 415-A.
The power supply is faulty, no votltage out to the amplifier.
The Mosfets are blown. I've changed the mosfets and it's driver, and still have a problem.
I tried to switch on but only one of the mosfets gets hot (the one which switches the 310. There are 2 of them - Mos5 in the scheme).
Obviously I turned it off.
1) What causes it to heat?
2) Testing the VCC of the LMC555, it's only 2.7V. When taking it out of the circuit, it's 12VDC! What makes the voltage to drop. Where does the supply of the LMC555 come from? The VCC of the 555 should be around 10V, as compared with a good card.
I've changed the 555, but the problem remained. I've checked the components around, resistors and capacitors, and transistors, and seem to be OK.
4) The VCC of the Mosfet driver is 10V, but should be 12V if compared with a good card.
3) Could the trafo be damaged? Are these parts reliable or may blow up?
4) What is the purpose of the optocoupler in the circuit?
I would really appreciate any help.
I didn't find the 100% schemes for this RCF (400), but found a very similar one (The 600 version).
name and a link here to download the pdf.
DigiPRO600B
https://elektrotanya.com/db-technologies_digipro600b_sch.pdf/download.html
Regards and many thanks
Szervusztok!
Panasonic SA-GX170 a hangerőpotm. feltekerésekor "overload"-ot ír kikicsivel a ventillátor elindulása után. (Szerintem) az IC jó, a feszültségei rendben vannak, így azt gondolom, a végfokok jók. Bemenő jel nélkül is ezt produkálja. A forrasztásokat már átnéztem, mert sokszor találkoztam már azzal, hogy vagy a végfok, vagy a stab.tok lábainál elengdnek a forrasztások.Tudna valaki tippet adni, hogy mit érdemes átnézni?
Köszönettel:
Attila
Panasonic SA-GX170 a hangerőpotm. feltekerésekor "overload"-ot ír kikicsivel a ventillátor elindulása után. (Szerintem) az IC jó, a feszültségei rendben vannak, így azt gondolom, a végfokok jók. Bemenő jel nélkül is ezt produkálja. A forrasztásokat már átnéztem, mert sokszor találkoztam már azzal, hogy vagy a végfok, vagy a stab.tok lábainál elengdnek a forrasztások.Tudna valaki tippet adni, hogy mit érdemes átnézni?
Köszönettel:
Attila
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce