Service manuals, schematics, eproms for electrical technicians

VESTEL 11AK19E3-24C08-SDA545XOTP B13-A51EBV13X09

TV - EPROM
Type: (TXT)
Size
65.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar vestel manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    VESTEL 11 AK 19 324 08 SDA 545 XOTP 13 51 EBV 09 11AK19E3 24C08 SDA545XOTP B13
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
17PW07-2 Vestel táp halott
Sziasztok!

Fent nevezett tápegységű készülék (SHARP LC40LE510E) nem csinál semmit.
Nem is tud, mivel a táp mindkét biztije F100, F101 elvillant. A PFC árammérő söntje R109 0,22 Ohm szakadt, és a +400 V bus kondiknál a fólia is égett. Tehát valami erősen ette a villanyt
Eddig semmi más zárlat jellegűt nem találtam. (FET-eket nem szedtem ki, ott még lehet szakadás). A hibákat megszüntettem.
Most viszont a 400 V az 327 V (úgy gondolom, míg STBY van, ez OK, bár nem tudom).
A rajz kissé átláthatatlan számomra (nagyon széttagolt és nem kereshető a PDF), valamint (jó)pár alkatrész nincs beültetve.
A 4.25 V STBY_1 villany viszont 0,5 V.
Azt gondolom, a STBY-nak akkor is lennie kellene, ha a MainBoard-al nincs összekötve, bár az IC302 opto körüli rész mágikus szerkezet.
A STBY szekunder része nem zárlatos, mégis "csuklik" az FDSL321 (IC301). Ezért arra gondolok, hogy az OVP szólal meg.
"4.4 Over Voltage Protection (OVP) : In the event of a malfunction in the secondary side feedback circuit, or an open
feedback loop caused by a soldering defect, the current through the opto-coupler transistor becomes almost zero
(refer to Figure 5). Then, VFB climbs up in a similar manner to the over load situation, forcing the preset maximum current
to be supplied to the SMPS until the over load protection is activated. Because excess energy is provided to the output,
the output voltage may exceed the rated voltage before the over load protection is activated, resulting in the breakdown
of the devices in the secondary side. In order to prevent this situation, an over voltage protection (OVP) circuit is
employed. In general, Vcc is proportional to the output voltage and the FPS uses Vcc instead of directly monitoring the
output voltage. If VCC exceeds 19V, OVP circuit is activatedr esulting in termination of the switching operation. In order
to avoid undesired activation of OVP during normal operation,Vcc should be properly designed to be below 19V."
Nos, a VCC majdnem 20 V-ig ugrik.
Bár a visszacsatoló optót (IC300) sem ellenőriztem még.

Valaki találkozott már hasonló problémával? Kérem segítsen!
Köszönöm:
Péter
ORION LCD T32-D VESTEL 17MB60-3 stby LED villog, firmware után nincs kép, de az OSD és txt működik. [MEGOLDVA]

Sziasztok!

Létezik ehhez a laphoz USB-s frissítés? Sajna csak MB62-höz találtam fájlokat.

https://elektrotanya.com/westwood_19v1led_ch_17mb60_firmware.rar/download.html
Ezzel ugyan elindult, behangoltam, de azt írja, video nem található, hang van, kép nincs.

Vestel AK36 alaplapos tévénél az OSD/TXT fényerejét szervízmenüből lehet növelni?MEGOLDVA!
Sziasztok! A tévén a kép jó de az OSD/TXT fényereje kicsit sötétebb.Nem akarok a szervíz menüben összevissza állítgatni.Valaki tudja lehet e itt külön növelni rajta,illetve melyik paramétert keressem? Üdv! Laci
Vestel 72cm-es tv 11AK28-6 os sasszéval MEGOLDVA! (Táphiba C130 halála ismét)
Üdv urak! A fent említett gépet buzerálom épp. Egyik haveré, és a következőképp állt meg: Reggel nézték, egyszercsak hirtelen standby-ba váltott, majd pár perc múlva egy csettenés és holt csend! A hálózati kisautomatát is levágta, de a TV saját biztije ép maradt! Ez a biztosítók szelektivitása szempontjából szerintem elég érdekes:D HI-HI:D No én eddig a következőket találtam: Q101 20A 600V fet zárlatos minden lábára! D105 szintén zárlatos! A kérdéses alkatrészeket megrendeltem, a kérdésem az volna, hogy mit nézzek meg esetleg még, esetleg mik a tipikus hibái, vagy tudtok e olyan alkatrészről ami alattomos módon nehezen deríthető ki hogy rossz... Előre is köszi a segítséget!
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce