Preview of LOEWEOPTA 547W KRONACH RECEIVER SCH [1st page] Click on the link for free download!
Advertisements
Please tick the box below to get download link:
Also known:
LOEWEOPTA KRONACH RECEIVER 547W 547
If you have any question about repairing write your question to the Message board. For this no need registration.
If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site. Have a nice Day!
Please take a look at the below related repair forum topics. May be help you to repair.
Warning! If you are not familiar with electronics, do not attempt to repair! You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived, so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Sziasztok!
Adott egy Ecler Pam 880 végfok. Összes fet, meghajtó, elégett ellenállás, stb cserélve lett. El is indul, de nagyon magas a nyugalmi áram. (300mA kb) Ennek következtében a meghajtó feteknél lévő feszültség értékek sem stimmelnek. A rajz fent van itt a tanyán. Szinte ugyan az, mint a Pam 960 és társai. D101 és D102 valamint D103 D104 zénerek között 6,2V-ot kellene beállítani. (+ és - tápág). A negatív oldalon ez meg is van, de a pozitiv oldalon max 3,7V-ig tudom ezt az értéket növelni, de ilyenkor már teljesen le van tekerve a nyugalmi áramot beállító trimmer, kb 250mA-re megy le a nyugalmi áram. Ugyan azok a típusú alkatrészek kerültek beépítésre, mint amik voltak benne. Kérdésem az lenne, hogy R111 növelésével tovább csökkenthető lenne-e a nyugalmi áram és ez megoldás lehetne-e a problémámra, vagy valami más probléma van? Sajnos fetes erősítőkben nem igazán vagyok jártas.
Hi,
I am working on a Luxman L100 belonging to a friend. I noticed the following problems.
a) It takes about 12 to 15 secs for the relay to turn ON.
b) The relay does turn ON but both the "winker" bulb and "ON" bulb do not light
(both the bulbs are OK)
c) The "touch MUTE" is not working.
d) When switching on the 10Hz low cut filter, the relay cuts off and does not come ON until the switch is set in the centre(bypass). Can someone familiar with this amp, please help me out
Thanks
Carlos
"FONTOS! Olyan fórum téma nevet válassz, ami beszédes, minél pontosabban illeszkedik arra, amivel kapcsolatban írsz. Egy lehetséges jó elnevezés
pl: ORION LCD PT26S chassis 17MB12-2, a tápja nem indul
Az nem elég, hogy pl: "LG LCD-TV" vagy "HP laptop" és hasonlóak. Illetve érdektelen, nem releváns információt se tartalmazzon a cím!
A helytelenül elnevezett topik felfüggesztésre [F], majd 48 óra után törlésre kerül! Felfüggesztett állapotban nem tudnak mások addig hozzászólni, amíg ki nem javítod a címet.
A hibás cím utólagos javítása (48 órán belül) a "Szerkesztés" fülre kattintva végezhető el.""IMPORTANT! Select a forum topic name that is descriptive, more precisely matched to which you're writing about. A possible good name
eg, ORION LCD-2 17MB12 PT26S chassis, the power supply for will not start
It is not enough, for example: "LG LCD TV" or "HP laptop" and the like. And do not include irrelevant information not relevant to the title!
The incorrectly named topic suspended [F] and will be deleted after 48 hours! Suspended while others are not able to speak until you correct the title.
Subsequent repair of defective title (within 48 hours) by clicking the 'Edit' tab to be done."
A barátom cd játékosa került hozzám nemrég, a sztori úgy indult hogy egyszer csak elhallgatott és se kép se hang, ennek 5 éve most elhozta hogy kukkolja már bele mi lehet a nyűgje, első bizti csere mivel ki volt égve, aztán ráköt a hifire és csak ilyen sercegéses zúgás tör elő belőle, cd bele olvas mindent, de a zene mellé párosul ez a búgó zúgó hang mintha test hiánya lenne de ezt átnéztem és minden rendben, ötleteket szivesen fogadok.
Egy kis videó arról hogy mi a hiba:
Sziasztok!
Hozzám került egy BEAG APT 100 végfok a panelon nem szakszerű munka eredményként pár pontatlan értékű ellenállást,diódát cseréltek ki.A kapcsolási rajz alapján ki is igazodtam,kivéve a D113,114 zénerek típusa nem szerepel a rajzon(érdekes!)Most 5.6voltosak vannak benne,de ez nem biztos mert ahová sima dióda kellet volna oda pedig zénert tettek,egy dióda helyére pedig 2.2 kohmos trimmer potit-ez még érdekesebb.
Köszönöm előre is!
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test or write your question to the Message board without registration. You can write in English language into the forum (not only in Hungarian)!