Service manuals, schematics, eproms for electrical technicians

RACAL DANA MODEL 9926 AND 9927 FREQUENCY METERS UP TO 1,3 GHZ

METER - SERVICE MANUAL
Type: (PDF)
Size
1.2 MB
Page
42
Category
METER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar racal manual?
Advertisements
Document preview [1st page]
RACAL DANA MODEL 9926 AND 9927 FREQUENCY METERS UP TO 1,3 GHZ service manual (1st page)
Preview of RACAL DANA MODEL 9926 AND 9927 FREQUENCY METERS UP TO 1,3 GHZ [1st page]
Click on the link for free download!
Document preview [2nd page]
RACAL DANA MODEL 9926 AND 9927 FREQUENCY METERS UP TO 1,3 GHZ service manual (2nd page)
Preview of RACAL DANA MODEL 9926 AND 9927 FREQUENCY METERS UP TO 1,3 GHZ [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    RACAL DANA MODEL METERS UP TO 9926 AND 9927 FREQUENCY GHZ
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant METER forum topics:
EMG-1353 (TR-1453) AC voltmérő beállításában kérnék segítséget
Sziasztok,

A címben szereplő műszer javításához szeretnék műszaki támogatást kérni. A készülék rajzát megtaláltam a Interneten keresgélve a 2003/1 Hobby Elektronika folyóiratban. A kapcsolási rajzon kívül keresem a szervizkönyvét esetleg részletező leírás a beállításáról, milyen jellel kell meghajtani, benne milyen jelszinteket kell beállítani, stb...

Köszönöm a segítséget!
Üdv
M.
 
HAINA szintező lézer vezérlése nem indul
Üdv Mindenki!

Hoztak hozzám egy HAINA típusú önbeálló szintező lézert.
A táp részét sikerült megjavítanom, de a szintezést vezérlő rész nem működik annak ellenére, hogy az IC-je megkapja az 5 V-os tápot. Sajnos erről az IC-ről a felirat le van dörzsölve, így nem tudom beazonosítani. 4 vékony zománcozott huzal megy a komplett szintezőblokkra (Vcc, H, V1,V2).
Mi lehet ennek az IC-nek a típusa, illetve milyen elven működik ennek a szintezőnek a motor és lézer vezérlése?
Várnám szíves segítségeteket.

Köszi
Elektronika autoindikator AI-01 (ciril) beüzemelése! Kész! Megoldva!
Tisztelt Szakik! A címben említett készüléket szeretném beüzemelni. A csatolt képek alapján kérnék ehhez segítséget a bekötéshez. Itt a tanyán megtaláltam a leírást, oroszul. Köszönettel Döme Attila

A bekötés megtörténte után (hosszas kísérletezés)szükséges volt a kijelző csere. Ami bevált!!!
(a rendelés szintén hosszas körülményes procedúra volt, végeredményben megérte.)
Köszönöm mindenkinek a hozzászólást.
Külön köszönet Unimannak az ebay link-ért.
Tisztelettel Döme Attila

(Más kérdés hogy nem merem használni nehogy tönkremenjen, megint :) )
 
Gould dso420 oscilloscope no horizontal deflection
Hello to everybody,
I have bought a defective Gould oscilloscope DSO420. At the beginning of the repair the power fuse was blown immediately after inserting the power plug: The RF-filter connector was shorted. Okay, ignore the RF-filter for now. 
Some leaked capacitors were within the power supply, all renewed as well as the NiMh accumulator.
Now most of the scope is running:: All LED at the front as well they are switchable and the screen of the scope was lightened th but only a vertical line is shown. No horizontal deflection at all. 
The circuit I have attached, all semiconductor are renewed, no change. The electrolytics are renewed, no change. Allways a vertical stroke. Does anyone have an idea?

Regards from Hamburg
Jens
 
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce