Service manuals, schematics, eproms for electrical technicians
SONY DSC-H1 SUPP ADJUSTMENT VER1.3
Type: 
(PDF)
(PDF)Size
82.0 KB
82.0 KB
Page
3
3
Category
STILL CAMERA
SERVICE MANUAL
STILL CAMERA
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Advertisements
Document preview [1st page]
Click on the link for free download!
Document preview [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
SONY DSCH-1 ADJUSTMENT DSCH1 SUPP DSCH DSC H1 DSC-H1
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant STILL CAMERA forum topics:
A sony-trv255e kamerám a kijelzőn szüke csíkok vannak.
A könyve azt írja koszos a fej.Régebben volt szervízbe,ott is azt
írták fejtisztítás. Majd fél év múlva ue. hiba.Félreraktam, vagy
két hónap múlva semmi baja. Öt kazetta után megint rossz.Kiváncsi
lennék volt e ilyen valakinek,mert csodálkozom a koszos fej magától nem szokott megtisztulni.Azon gondolkozom nem e a mechanika szívat.
Érdekelne a véleményetek,érdemes e szétszedni.
Sziasztok!
C32:30 és C31:30 hibakódot jelez a kamera. A kazettát nehezen veszi be,/resetelni kell/ bevétel után pörgeti balra aztán jobbra próbálná, de csak hang van fizikailag nem teker ekkor adja a C32.30 hibakódod. A kazetta ajtó kapcsolója eltörött azt helyettesítettem egy nyomógombbal ideiglenesen.
Üdv.
zaza99
Sziasztok!
Olyan gondom lenne a fent nevezett készülékkel, hogy amikor felvételt készítek akkor szakadozik a hang, ill. pixeles lesz a felvétel. De csak akkor ha a kamerát mozgatom ha egy pontra nézek vele akkor nem.
Mi lehet ez?
Üdv Sanyi
Hi friends,
I would like to make adjustments to my Sony DSC-F717.
According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.
If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
I would like to make adjustments to my Sony DSC-F717.
According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.
If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce