Service manuals, schematics, eproms for electrical technicians

TEKTRONIX 576 CURVE TRACER SM

METER - SERVICE MANUAL
Type: (PDF)
Size
24.3 MB
Page
251
Category
METER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar tektronix manual?
Advertisements
Document preview [1st page]
TEKTRONIX 576 CURVE TRACER SM service manual (1st page)
Preview of TEKTRONIX 576 CURVE TRACER SM [1st page]
Click on the link for free download!
Document preview [2nd page]
TEKTRONIX 576 CURVE TRACER SM service manual (2nd page)
Preview of TEKTRONIX 576 CURVE TRACER SM [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    TEKTRONIX TRACER 576 CURVE
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant METER forum topics:
Tektronix 7633 readout repair
I have a problem with the Tektronix 7633rd Readout is not working. Displays only the spot, (no time base on the screen), from time to time, jump to the next position where it should be readout. After adjustment knob charcter scan, there's a readout, but the characters were, or blurred, or not drawn to the end - in pieces, imposed on themselves. The readout is off everything works. For all kinds of advice I would be very grateful.
Tektronix 485 oszcilloszkóp javítás
Kedves Fórúmozók.

Egy tektronix 485 tip. oszcilloszkóp javításához szeretnék segítséget kérni. A műszer kicsit viharvert állapotban került hozzám,pár gomb hiányzik.Belül érintetlennek látszik,nincs jele semilyen  beavatkozásnak. Bekapcsolás- sem idővonal,sem fénypont finderrel.Először végigmértem a tápfeszültségeket,tizedre pontosak,annak ellenére,hogy több mint 40 éves készülék.Próbálgatás kapcsolgatás,majd az x-y állásban megjelent a fénypont,pontosabban egy kb. 5x5 mm-es négyszög.Mivel automata fókusz szabályozás van gondolom ennek egy 
pontnak kellene lenni. Az A csatorna potival eltolható le-fel. A B csat-val számomra érthetetlen módon nem le-fel,hanem jobbra balra tolható.A horizontális pozició potméterre nem reagál.
A fénypont a többi kapcsoló állásnál eltünik.Egyenlőre eddig jutottam,előre is köszönöm a segítséget
Tektronix 2225 oscilloscope a képernyő bal oldalán erős világító pont látható Megoldva
Sziasztok Tek. 2225 scopon a képen látható hiba javításához kérnék segítséget. SM letöltve, all tápfesz megfelelő. A fénypontot el tudom mozdítaani a hor.pozition gombbal.A scope múködik, senki nem matatott benne. Müködö oscilloscopom van. Nem tudom, hogy a képek átmennek-e Köszönettel Gyuri
Tektronix 2215 oszcilloszkóp, a két csatorna összegzése esetén 1 cm ofszet hiba keletkezik. Miért?
Sziasztok! A fenti szkóp beállítása a leírásnak megfelelően megtörtént. A két csatorna bemenete GND-re kapcsolva. Mindkét sugarat pontosan középre állítva, ha összegzem a két jelet (Both & ADD) beállításban a sugár közel 1 centit lefelé mozdul. Nem találtam erre vonatkozó beállítást. ALT és CHOP módban a két vonal pontosan fedi egymást (jel esetén is). A két csatorna erősítése is egyforma (külön mérve). Az CH2 jele invertálható, de azt is beállítottam úgy, hogy az INV ki-be kapcsolásakor a sugár nem mozdul el középről. A rajz alapján diódamátrixokkal kapcsolgatja a csatornákat, csak az nem világos, hogy ha mindkettő külön- külön DC-ben középen van, akkor összeadva miért mozdul el a sugár? Üdv.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce