Service manuals, schematics, eproms for electrical technicians

USSR GIALA 406.

AUDIO - SERVICE MANUAL
Type: (DJVU)
Size
26.5 KB
Page
1
Category
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar ussr manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    USSR GIALA 406. 406
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Welt bild DAB632 hifitorony rádió nem szól
Sziasztok !
Adott a fenti music center .Az állomásokat megtalálja  RDS -t kiírja de hangot nem ad! A tuner egy QANTEK Q8+ tuner modul ,már annak a kimenetén sincs hang ! Ha valaki találkozott már evvel a hibával várnám segítségét!
Üdv!
HK HD740 CD lejátszó csak sokadszorra olvassa be a lemezt
Üdv!
Még soha meg nem bontott CD játszó műsoros, vagy írt lemezt csak sokadszorra olvassa be, visszaadja a tálcán a lemezt.
Ha egyszer beolvasta, azt a lemezt bármikor, a készülék akár több napi kikapcsolása után is "látja" és lejátsza.
Szét nem bontottam, a készülék nincs nagyon elhasználva, bemutató darabként vettem évekkel ezelőtt.
Ez már Kínában készült.
Nem tudom, ennyi infóra tudna-e segítséget, ötletet adni valaki.
Köszönöm!
 
KENWOOD KRC-194YG autórádió nem kapcsol be
Sziasztok Mesterek! Adott a címben szereplő autórádió (rajz a tanyán). Amikor bedugom a táp(stb.) csatlakozót, 2 másodpercre felvillannak az előlap fényei és megjelenik az "ALL OFF" felirat, majd teljes sötétség és néma csend. Innentől csak a reset gombra reagál. Ha ezt megnyomom, ismét felvillannak a fények, ua. a kiírás, aztán megint csend. A BackUp +5V megvan, de állandó jelleggel jelen van a PowerOn +5V, és a +8V is. Az én értelmezésemben utóbbi kettőnek csak bekapcsolt állapotban kellene megjönnie. Vagy rosszul gondolom? Mellesleg a BackUp +5V-ot kapcsoló tranyó olyan forró, hogy az ujjam 1mp-nél tovább nem bírja. (De a fesz megvan és stabil.) Próbáltam másik előlappal is, de azzal is ua. Végső esetben szerzek mégegy ilyen rádiót és összehasonlító méréseket végzek. De ez valszeg csak holnap lesz. Addig is minden ötletet szívesen vennék! Köszönettel: Gyula
Barometric Pressure Sensor: BMP280 / BME280 – Basics, Wiring, and Arduino Example

Hello everyone,

I wanted to share some insights about the BMP280 and BME280 barometric pressure sensors. These modules are widely used in environmental monitoring, IoT, and weather-related projects.

Overview
  • The BMP280 measures temperature and pressure.

  • The BME280 adds humidity measurement to the same compact design.

  • Both communicate through I²C or SPI interfaces.

  • They typically operate between 1.7 V and 3.6 V, so they are not directly 5 V tolerant.

Key Specifications
  • Pressure Range: 300–1100 hPa

  • Accuracy: ±1 hPa (typical)

  • Temperature Range: –40 °C to +85 °C

  • Humidity Range (BME280): 0–100 % RH, with ±3 % accuracy

Arduino Example Notes

When wiring to a microcontroller:

  • Connect SDA and SCL lines with pull-up resistors (usually 4.7 kΩ).

  • Use the 3.3 V power supply pin.

  • Typical I²C addresses are 0x76 or 0x77, depending on board configuration.

  • The Adafruit BME280 library works well for both BMP280 and BME280.

Discussion Points
  1. Has anyone compared accuracy between BMP280 and BME280 in long-term use?

  2. What kind of digital filtering or averaging methods do you use to smooth out noisy pressure readings?

  3. For battery-powered setups, which mode do you prefer — sleep, forced, or normal — for the best power efficiency?

  4. How do you handle level shifting when using these sensors with 5 V microcontrollers?

  5. Any experience using these sensors for indoor altitude estimation?

These sensors are compact, reliable, and quite easy to integrate. I’d love to hear how others are using them in their weather or IoT projects!

Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce