You are here

Koban KP-03 Current Clamp Meter DMM, C31 Burn

16 posts / 0 new
Last post
neuron
neuron picture

The factory / reseller ... don't know anything about the device (Schematic, Service manual, etc) :(
and I need to repair this DMM - Clamp Meter.

2TY - Transistor - Q5 (Diode mode ok)

CHX ??? 5 Pins - U3

C31 ??? Burn, :poof:

Tested - V, Ohm, Diode, ºC ... don't see any errors

Thanks in advance for all info

Ruy

File attachment: 
Comments
Mosószaki
Mosószaki picture

Burnt pcb. Discard pcb.

0

neuron
neuron picture

Only C31 ...
the rest survive

0

Mosószaki
Mosószaki picture

Én elhiszem neked, hogy az alkatrészeket ki szeretnéd cserélni!
De te meg hidd el nekem, hogy amég a szét égett panelt ki nem fűrészeled és meg nem építed, akár légszerelésel is a fóliázat mintázatának az utánzatát, addig csak egy nagy kuka az a DMM...
Tehát kezd a panel fűrészelésével!
Ha az kész és merev drótokból megépítetted a fóliázat mintáját, hát esse kavics, tedd rá az alkatrészek..
Aztán 99% az esélyed, hogy a DA is kapott a pofonból és mégis kukában fogja végezni a szerkezet.

0

zsugori
zsugori picture
***
File csatolás: 

0

neuron
neuron picture

Thank you very much.

Please describe your procedure ... that I can follow.

Ruy

0

zsugori
zsugori picture
***

1

0

neuron
neuron picture

Thank you zsugori,

2TY 2 - Emitter -> down -> 2 Layer, through hole.
2 - Emitter -> up , Left -> C letter ->
U3 pin 2 VSS -> C31

U3 - pin 1 (down) -> 2 Layer, through hole -> the other C31 pin

Testing U3 (Diode Mode) I get +- 0,56V
Other procedure to test this IC?

In https://cdn.datasheetspdf.com/pdf-down/H/T/7/HT7540-1_HoltekSemiconducto... pag. 12
"Application Circuits" with TR1?

Merry Christmas,
Ruy

0

zsugori
zsugori picture
***

rotary switch semmi köze hozzá tr1-hez

0

neuron
neuron picture

Thank you zsugori,

Wow

Test with 10 uF? in circuit

Ruy

0

Kari
Kari picture
*****

Hi Neuron,
give us knwoed your clampmeters exact type Nr please. https://www.google.com/search?q=KOBAN+-+CURRENT+CLAMP+METER&rlz=1C1LRNT_...

0

Mosószaki
Mosószaki picture

Szia Kari!
Írd meg az úriembernek, hogy fűrészelje ki az elégett paneldarabot! 
Teljesen, sehol ne hagyjon elszenesedett panelt! 
Aztán építse újra a fóliázatot és utána keressen tranzisztrort! 
Apropó! Túlélte az AD ezt a szenesedésd? 
Ki kellene próbálni,ert lehet kuka az egész... 
Szia! 
 

0

neuron
neuron picture

Please see the full image of Koban

KP - 03

Regards Ruy

File csatolás: 

0

torokj
torokj picture

Hi Neuron!
Did the AD converter chip "survive" this shock?
First of all,try it.
After remove  (with a small saw )the burned PCB ,than rebuild that  circuit part.
It seems a hard mission...
Good luck,
TJ
 

0

AzzA
AzzA picture
*

One fool makes a hundred

0

neuron
neuron picture

Tested - V, Ohm, Diode, ºC ... don't see any errors
The measure ... results ok

Please the procedure.
The only part is the C31, the rest of the board survive.
Ruy

0

Sponsored links