Service manuals, schematics, eproms for electrical technicians

LIFETEC LF3751 11AK20S

TV - EPROM
Type: (RAR)
Size
246.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar lifetec manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    LIFETEC LF-3751 LF3751 11AK20S LF 3751 11 AK 20
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Orion T2835 STX
Szűkségem lene Orin T2835 stx tápegzség rajzára ami fönt van a honlapon nem stimel. három tranyistoros a táp, szétdurantak. Tranyistorok KOR1802, 2SC3807 és a zener is tönkre ment nem tudom leolvasni. Mit lehet a KOR1802 helyet teni
Orion T2915SPTX sortáp alacsony MEGOLDVA!!!!
Üdv Mindenki! Elromlott hőn szeretett tv-nk, 11AK19P5 sasszival. A hiba azzal indult, hogy időnként fekete, cirádákkal tűzdelt sáv jelent meg a képernyő bal oldalán és közben változott a sor és függméret is, majd egy kis idő után minden beállt a helyes működésre. Időszakos hiba lévén nem foglalkoztam vele, gondoltam, majd ha egyértelmű lesz a dolog. Tudtam, hogy valamelyik láb elmelegedett és kontaktos és hirtelen én a függ IC-re gondoltam, de csak gondolat maradt. Miután végleg megadta magát, nosza szedjük szét, mert így már biztosan kimérhető a hiba. A táp primer körében egy hűtőzászlóval ellátott, kis panelkén elhelyezett D822 pozíciószámú diófa lába melegedtek el, de mindenhol. Megforrasztottam, de sajnos nem indul a gépes, illetve próbál, de rövid próbálkozás után visszaáll készenlétbe. Sorfokot lekötve és a 150μH helyére egy 60W-os izzót applikáltam, majd a tv-t indítva egy pillára az izzó felvillan halványan, majd beáll készenlétbe. Na, mondom a táp jó, ...de nem, mert elindítva a gépet a táp kimenetein +9,1V, +14V, +16,7V,-16,4V és +42V(!) jelent meg és az izzó ugye emiatt haloványan világított folyamatosan. A távszabályozóra nem reagál semmit. Az MC44603 IC tápja beáll a +13,5V-ra készenléti állapotban, indítás után pedig 15V-ra emelkedik. A sortáprészen kicseréltem az első 47μF-os kondit, mert pupulykás volt, a diófát csak ellenőriztem. Mi okozhatja a sortáp alacsony feszét?
Sony KV-29X5D
Üdv mindenkinek! Úgy hozták ide hogy váltogatta a csatornákat. Nyomógombokat kivettem, a csatorna váltás megszűnt. De csak két csatornát ismer (00, és 01) és azokon sem jön adó. És nem is mindig indul olyankor 2-t villog, gondolom valami hibakód. Mi lehet ez? Memória? Esetleg proci? Vagy esetleg az adatvonalon meghűlyíti valami? Köszönöm előre is!
Philips 40PFL7007K/12 does not power on - Chassis QFU1.1E LA
Hi everybody, I have Philips 40PFL7007K/12 on repair. TV does not start up. I have checked the PSU and it seams to be OK. There seam to be problem on the main board. What I have tried… Well, there is +3V3-STANDBY coming from PSU to main board. This feeds up the main processor. This voltage has also been used to switch TV on. I have checked that switching signal from POWER ON button goes back to main board. But I did not check this whole path towards the processor as it is BGA package and it is covered by ceramic cooling plate. And here comes what is not clear to me. 1. How to check if the main processor works? Does it work on the +3V3-STANDBY when TV is is standby mode? 2. Can I somehow check if the PSU is working? May be by activating some pin? 3. I have noticed by measuring (ohm-meter) some capacitors on the main board (in circles on the picture) that there is very low resistance on them (4.5ohms). In the scheme it is shown that these capacitors are on the 1V5 (1.5V) line. Is this OK? Basically it does not give much current as I = 1V5 / 4R5 = 333mAmps. What do you think? Certainly there are low voltage data parts (RAM. Processor …) connected and such resistivity might be correct….?.... What I have also find that this 1V5 is split into 1V5M0 and 1V5M1. See the picture. I have removed the coils and measured resistance. Then 1V5M0 shows about 15ohms and 1V5M1 shows about 6,5ohms. The service manual is on this link: http://elektrotanya.com/philips_ch.qfu1.1e_la.pdf/download.html Thanks Martin
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce